Kit for workbench frame manufacturing.

Length, width, height and tube size are configurable.

Kit Specifications:

• Supporting Points: 4
• Tubes Material: S235 Steel laser cut tubes and plates.
• Surface Treatment: No treatment
• Screws kit included for leveling to the ground
• Assembly: This product needs welding for assembly
• Assembly instructions included

LAM Recommendations:

• It is recommended to follow the assembly instructions to get best results
• If desired it can be applied painting on the product once assembled for better preservation against oxidation

NOTE: Contact with LAM for any different configuration than available in the product form.

Kit for workbench frame manufacturing. “H” lower frame.

Length, width, height and tube size are configurable.

Kit Specifications:

• Supporting Points: 4
• Tubes Material: S235 Steel laser cut tubes and plates
• Surface Treatment: No treatment
• Screws kit included for leveling to the ground
• Assembly: This product needs welding for assembly
• Assembly instructions included

LAM Recommendations:

• It is recommended to follow the assembly instructions to get best results
• If desired it can be applied painting on the product once assembled for better preservation against oxidation

NOTE: Contact with LAM for any different configuration than available in the product form.

Kit for Riser Block manufacturing to use on your welding table.

The perfect solution for projects where working at different heights is needed (frames, chassis, piping, etc.)

Also useful to extend your LAM welding table (only possible on BL81001).

Length, width and height are configurable.

Kit Specifications:

Material: Steel S355
Treatment: No treatment
Assembly: This product needs welding for assembly
Assembly instructions included

LAM Recommendations:

It is recommended for maintenance to apply lubricant (for example WD40 or similar product) as a protection against oxidation while not using
It is recommended to use an anti-spatter spray while working to avoid welding spatters stick to the surface
It is not recommended to paint the product. The conductive properties may be affected for welding works
It is recommended to follow the assembly instructions to get best results

NOTE: Contact with LAM for any different configuration than available in the product form.

Kit for workbench frame manufacturing. “U” lower frame.

Length, width, height and tube size are configurable.

Kit Specifications:

• Supporting Points: 4
• Tubes Material: S235 Steel laser cut tubes and plates
• Surface Treatment: No treatment
• Screws kit included for leveling to the ground
• Assembly: This product needs welding for assembly
• Assembly instructions included

LAM Recommendations:

• It is recommended to follow the assembly instructions to get best results
• If desired it can be applied painting on the product once assembled for better preservation against oxidation

NOTE: Contact with LAM for any different configuration than available in the product form.

Stop tab to use on workbench/welding table.

Length, hole diameter and thickness are configurable.

Specifications:

• Material: Steel S355
• Treatment: No treatment
• Lock-bolt kit not included, sold separately (product AC86004)

NOTE: Contact with LAM for any different configuration than available in the product form.

Stop tab to use on workbench/welding table.

Length, hole diameter and thickness are configurable.

Specifications:

• Material: Steel S355
• Treatment: No treatment
• Lock-bolt kit not included, sold separately (product AC86004)

NOTE: Contact with LAM for any different configuration than available in the product form.

Stop tab to use on workbench/welding table.

Length, hole diameter and thickness are configurable.

Specifications:

• Material: Steel S355
• Treatment: No treatment
• Lock-bolt kit not included, sold separately (product AC86004)

NOTE: Contact with LAM for any different configuration than available in the product form.

Double grinder holder to use on workbench/welding table or wall installation.

Grinder disc diameter is customizable.

Specifications:

• Material: Steel S235
• Treatment: No treatment

NOTE: Contact with LAM for any different configuration than available in the product form.

Grinder holder to use on workbench/welding table or wall installation.

Grinder disc diameter configurable.

Specifications:

• Material: Steel S235
• Treatment: No treatment

NOTE: Contact with LAM for any different configuration than available in the product form.

Lock-bolt kit for accesories fixation on workbench/welding table.

Washer thickness and hole diameter are configurable.

Specifications:

• Bolts: 4 shoulder bolts Ø16x25mm
• Washers: 4 spacing washers
• Nuts: 4 M12 wing nuts

NOTE: Contact with LAM for any different configuration than available in the product form.

Kit for vise extension manufacturing (three anchor points) to use on workbench/welding table.

Length, width, depth, hole diameter and offset are configurable.

Kit Specifications:

• Material: Steel S355
• Treatment: No treatment
• Assembly: This product needs welding for assembly

Only compatible with the block BL81001.

NOTE: Contact with LAM for any different configuration than available in the product form.

Kit for vise extension manufacturing (four anchor points) to use on workbench/welding table.

Length, width, depth, hole diameter and offset are configurable.

Kit Specifications:

• Material: Steel S355
• Treatment: No treatment
• Assembly: This product needs welding for assembly

Only compatible with the block BL81001.

NOTE: Contact with LAM for any different configuration than available in the product form.

Kit for workbench/welding table manufacturing (supporting rack not included, sold separately).

Specially created for light-weight works: small structures welding, tailpipes, supports, etc.

Length and width are configurable.

Kit Specifications:

• Material: Steel S355
• Treatment: No treatment
• Thickness: 6mm
• Hole Pattern: Ø16mm with 50mm of distance between holes
• Assembly: This product needs welding for assembly
• Assembly instructions included

LAM Recommendations:

• It is recommended for maintenance to apply lubricant (for example WD40 or similar product) as a protection against oxidation while not using
• It is recommended to use an anti-spatter spray while working to avoid welding spatters stick to the surface
• It is not recommended to paint the product. The conductive properties may be affected for welding works
• It is recommended to follow the assembly instructions to get best results

Only compatible with the following rack models:

• RC82007
• RC82008

NOTE: Contact with LAM for any different configuration than available in the product form.

Kit for adjustable square manufacturing to use on workbench/welding table.

It allows for pre-set positions at 0°, 30°, 45°, 60°, 90° and 120° or even free angle adjustment from 0° to 120°.

Hole diameter configurable.

Kit Specifications:

• Material: Steel S355
• Treatment: No treatment
• Assembly: This product needs welding for assembly
• Screws kit included for assembly

NOTE: Contact with LAM for any different configuration than available in the product form.

Kit for square manufacturing to use on workbench/welding table.

Length, height, width, and hole diameter are configurable.

Kit Specifications:

• Material: Steel S355
• Treatment: No treatment
• Assembly: This product needs welding for assembly

NOTE: Contact with LAM for any different configuration than available in the product form.

Kit for workbench/welding table manufacturing (supporting rack not included, sold separately).

Length, width, depth, hole diameter and material thickness are configurable.

Kit Specifications:

• Material: Steel S355
• Treatment: No treatment
• Assembly: This product needs welding for assembly
• Assembly instructions included

LAM Recommendations:

• It is recommended for maintenance to apply lubricant (for example WD40 or similar product) as a protection against oxidation while not using
• It is recommended to use an anti-spatter spray while working to avoid welding spatters stick to the surface
• It is not recommended to paint the product. The conductive properties may be affected for welding works
• It is recommended to follow the assembly instructions to get best results

Only compatible with the following rack models:

• RC82001
• RC82002

NOTE: Contact with LAM for any different configuration than available in the product form.